HSC Study

Quantitative Analysis

Standard solutions and titration technique, titration calculations including dilutions and back titrations, titration curves and conductivity graphs for strong and weak acids and bases, indicator choice, analysis in industry, by Aboriginal and Torres Strait Islander Peoples and with digital probes, household analyses, and buffers in the lab, blood and oceans.

100 min · Module 6: Acid/Base Reactions

Assumes you have read Using Brønsted–Lowry Theory.

The full teaching. Start here.

The short version

Titration reacts a measured volume of one solution with a solution of known concentration until the reaction is exactly complete.

  • The equivalence point is where the reactants have been mixed in the stoichiometric ratio.
  • The end point is where the indicator changes colour. A good indicator makes the two almost equal.

The calculation always runs the same way:

  1. Moles of the known solution: .
  2. Mole ratio from the balanced equation.
  3. Concentration of the unknown: .
  4. Undo any dilution.

Choosing an indicator. Pick one whose colour change range sits inside the steep part of the curve.

TitrationpH at equivalenceIndicator
strong acid, strong base7almost any (bromothymol blue, phenolphthalein)
strong acid, weak basebelow 7methyl orange or methyl red
weak acid, strong baseabove 7phenolphthalein

A buffer is a weak acid and its conjugate base (or a weak base and its conjugate acid) in similar amounts. It resists changes in pH when small amounts of acid or base are added:

Standard solutions

A standard solution has an accurately known concentration. You make one from a primary standard, a substance that is:

  • very pure;
  • stable in air (it does not absorb water or CO₂, or react with oxygen);
  • of known formula, with no variable water of crystallisation;
  • of high molar mass, so the percentage weighing error is small.

Anhydrous sodium carbonate (dried in an oven first) is the usual primary standard for acids. Potassium hydrogen phthalate is used for bases. NaOH is not a primary standard: it absorbs water and CO₂ from the air, so NaOH solutions are standardised by titration against a primary standard.

Making the solution.

  1. Weigh the solid accurately.
  2. Dissolve it in a beaker of distilled water.
  3. Transfer it to a volumetric flask, rinsing the beaker, stirring rod and funnel into the flask.
  4. Fill to just below the mark, then add water dropwise until the bottom of the meniscus sits on the mark at eye level.
  5. Stopper and invert to mix.

CheckpointAnswer before reading on.

Which property is NOT required of a primary standard?

Select one answer

Hint 1A primary standard must give an accurately known concentration.

Hint 2Think about purity, stability and mass.

Hint 3Which property is irrelevant or undesirable?

CheckpointAnswer before reading on.

What mass of anhydrous sodium carbonate (105.99 g mol) is needed to make 250.0 mL of 0.1000 mol L standard solution?

Hint 1n = cV with V in litres.

Hint 2n = 0.1000 × 0.2500.

Hint 3m = nM.

Exam question

Standard · about 5 min

3 marks

Describe how to prepare a standard solution of sodium carbonate in a 250.0 mL volumetric flask.

Hint 1Weigh accurately.

Hint 2Transfer every trace of solid.

Hint 3Make up to the mark carefully.

Where students lose marks on this one
  • Adding the solid straight to a full flask of water.

    Why it happens: The final volume must be exactly 250.0 mL.

    Dissolve first, then make up to the mark.

Written for this site.

Titration technique

  • Burette: rinse with the titrant. Read from the bottom of the meniscus to two decimal places.
  • Pipette: rinse with the solution it delivers. Let it drain and touch the tip on the side of the flask; do not blow out the last drop.
  • Conical flask: rinse with distilled water only. The pipetted aliquot fixes the moles, so extra water changes nothing.

Do one rough titration first, then repeat accurately until you have three concordant titres, all within 0.10 mL of each other. Average only the concordant titres.

CheckpointAnswer before reading on.

What is the difference between the equivalence point and the end point of a titration?

Select one answer

Hint 1One is theoretical, one is observed.

Hint 2Which is where the stoichiometric amounts have reacted?

Hint 3Which is where the indicator changes?

CheckpointAnswer before reading on.

In a titration, which piece of glassware should be rinsed with distilled water only (not with the solution it will hold)?

Select one answer

Hint 1Rinsing with the solution avoids dilution.

Hint 2But one vessel only receives a measured number of moles.

Hint 3Extra water there does not change the moles.

Worked example4 marks

Ethanoic acid in vinegar

10.00 mL of vinegar is diluted to 100.0 mL in a volumetric flask. 25.00 mL aliquots of the diluted solution need an average of 20.80 mL of 0.1000 mol L NaOH. Find the concentration of ethanoic acid in the vinegar in mol L.

Moles of NaOH

n = cV, with V in litres.

mol.

Moles of acid

CH₃COOH + NaOH → CH₃COONa + H₂O is 1 : 1.

mol in 25.00 mL.

Diluted concentration

c = n/V.

mol L.

Undo the dilution

10.00 mL was made up to 100.0 mL, a tenfold dilution.

mol L.

Answer

0.8320 mol L, which is about 50 g L of ethanoic acid.

Is that answer sensible?

Vinegar is typically around 4 to 5% ethanoic acid, or 40 to 50 g L, so the answer is sensible.

Exam question

Standard · about 5 min

3 marks

25.00 mL aliquots of 0.1000 mol L are titrated with HCl. The titres are 23.10 (rough), 22.45, 22.40 and 22.35 mL. Calculate the concentration of the HCl.

Hint 1Exclude the rough titre; average the concordant ones.

Hint 2.

Hint 3n(HCl) = 2 × n(Na₂CO₃).

Where students lose marks on this one
  • Including the rough titre in the average.

    Why it happens: The rough titre overshoots the end point.

    Average only concordant titres.

Written for this site.

Exam question

Harder · about 7 min

4 marks

10.00 mL of vinegar is diluted to 100.0 mL. 25.00 mL of the diluted solution needs 20.80 mL of 0.1000 mol L NaOH. Calculate the concentration of ethanoic acid (60.05 g mol) in the original vinegar, in g L.

Hint 1n(NaOH) = n(CH₃COOH) in 25.00 mL.

Hint 2Find c(diluted), then multiply by 10.

Hint 3Convert mol/L to g/L.

Where students lose marks on this one
  • Forgetting the dilution factor.

    Why it happens: The vinegar was diluted tenfold.

    Multiply by 10.

Written for this site.

Titration curves

A titration curve plots pH against the volume of titrant added. A pH probe and data logger record it directly.

pHpH = pKa = 4.748.77HClCH₃COOH1020304024681012volume of NaOH added (mL)
25.00 mL of 0.100 mol L⁻¹ HCl (solid) and of 0.100 mol L⁻¹ ethanoic acid (dashed), each titrated with 0.100 mol L⁻¹ NaOH. Both reach equivalence at 25.00 mL, but at pH 7 and pH 8.7 respectively. The weak acid has a buffer region with pH = pKa at half-equivalence.

Strong acid, strong base.

  • Starts at a low pH (1 for 0.1 mol L HCl).
  • Stays nearly flat, then rises very steeply from about pH 3 to 11 at equivalence.
  • Equivalence is at pH 7, because the salt (NaCl) does not hydrolyse.

Weak acid, strong base.

  • Starts higher (about 2.9 for 0.1 mol L ethanoic acid) because the acid is only partly ionised.
  • Rises quickly at first, then flattens into a buffer region where HA and A⁻ are both present.
  • At half-equivalence, , so . This is how you read off a curve.
  • Equivalence is above 7, because the conjugate base A⁻ reacts with water to form OH⁻.
  • The steep section is shorter (about pH 7 to 11).

Strong acid, weak base (for example, HCl added to NH₃).

  • Starts at about pH 11 and falls.
  • Has a buffer region where pH = of NH₄⁺ at half-equivalence.
  • Equivalence is below 7 (about 5), because NH₄⁺ is acidic.

Weak acid with weak base has no sharp vertical section at all, so no indicator gives a clear end point. These are not titrated with indicators.

The equivalence volume depends only on the moles of acid, not its strength. 25 mL of 0.1 mol L ethanoic acid needs exactly as much NaOH as 25 mL of 0.1 mol L HCl.

CheckpointAnswer before reading on.

Which indicator is most suitable for titrating ammonia solution with hydrochloric acid?

Select one answer

Hint 1Strong acid + weak base gives an acidic salt.

Hint 2Equivalence is below pH 7.

Hint 3Choose an indicator changing in that range.

CheckpointAnswer before reading on.

On the titration curve of a weak acid with NaOH, the pH at half the equivalence volume is 4.74. What is the Ka of the acid?

Select one answer

Hint 1At half-equivalence, [HA] = [A⁻].

Hint 2So pH = pKa.

Hint 3Ka = 10^(−pKa).

CheckpointAnswer before reading on.

Acid P has pKa 3.17 and acid Q has pKa 4.74. Which statement is correct?

Select one answer

Hint 1pKa = −log Ka.

Hint 2A smaller pKa means a larger Ka.

Hint 3Larger Ka means stronger.

Exam question

Harder · about 7 min

4 marks

Compare the titration curves obtained when 0.1 mol L⁻¹ NaOH is added to 25 mL of 0.1 mol L⁻¹ HCl and to 25 mL of 0.1 mol L⁻¹ ethanoic acid.

Hint 1Starting pH.

Hint 2Shape before equivalence and the pH at equivalence.

Hint 3Size of the vertical section.

Where students lose marks on this one
  • Saying the weak acid needs less NaOH.

    Why it happens: Equal moles of monoprotic acid need equal moles of base.

    Strength does not change the equivalence volume.

Written for this site.

Exam question

Hardest asked · about 6 min

3 marks

25.00 mL of 0.100 mol L ethanoic acid () is titrated with 0.100 mol L NaOH. Calculate the pH at the equivalence point.

Hint 1At equivalence: 0.00250 mol CH₃COO⁻ in 50.00 mL.

Hint 2.

Hint 3.

Where students lose marks on this one
  • Saying pH = 7 at equivalence.

    Why it happens: The ethanoate ion is basic.

    Hydrolysis of the conjugate base.

Written for this site.

Common mistake

The equivalence point of every titration is at pH 7.

Why it happens: Neutralisation sounds like it should give a neutral solution.

Only a strong acid with a strong base gives a neutral salt. With a weak acid, the conjugate base makes the solution basic at equivalence. With a weak base, the conjugate acid makes it acidic. This is exactly why indicator choice matters.

Change the acid below to compare curves. Slide pKa below zero for a strong acid, then raise it and watch the starting pH, the buffer region and the equivalence pH all rise. The shaded band is the colour change range of the best indicator.

Titration curve of an acid with sodium hydroxideTitrating 25.0 mL of 0.1 mol per litre weak acid, pKa 4.8 with 0.1 mol per litre sodium hydroxide. The pH starts at 2.90, the equivalence point is at 25.00 mL with pH 8.75.equivalence0510152025303540455002468101214volume of NaOH added (mL)pH
  • pH
  • half equivalence: pH = pKa
For a weak acid the curve starts higher, rises gently through a buffer region and has a shorter, higher vertical section, so the equivalence point is above 7. At half the equivalence volume, pH = pKa: that is how pKa is measured from a titration.
4.8
0.10 mol L⁻¹
0.10 mol L⁻¹
Acid
weak acid, pKa 4.8
Starting pH
2.90
Equivalence volume
25.00 mL
pH at equivalence
8.75
pH at half equivalence
4.80
Suitable indicator
phenolphthalein

Every slider is a normal range input, so the arrow keys move it one step and Home and End jump to the extremes.

Conductivity graphs

Conductivity depends on how many ions are present and how fast they move. H₃O⁺ and OH⁻ move much faster than any other ion.

HCl with NaOH: a V shape.

  • Before equivalence conductivity falls: each OH⁻ added removes a very mobile H₃O⁺ and leaves behind a much slower Na⁺.
  • At equivalence it is at a minimum (only Na⁺ and Cl⁻).
  • After equivalence it rises steeply, as excess OH⁻ and Na⁺ build up.

Ethanoic acid with NaOH.

  • Starts low, because a weak acid has few ions.
  • Rises gently as un-ionised CH₃COOH is converted into Na⁺ and CH₃COO⁻.
  • Rises more steeply after equivalence, from the excess OH⁻.
  • The equivalence point is where the gradient changes.

Strong acid with weak base (HCl titrated with NH₃). Conductivity falls as H₃O⁺ is replaced by NH₄⁺, then levels off after equivalence, because excess NH₃ is barely ionised.

The advantage of a conductometric titration is that it needs no indicator, so it works for coloured or cloudy solutions and for weak acid with weak base.

CheckpointAnswer before reading on.

During a conductometric titration of HCl with NaOH, conductivity falls to a minimum and then rises. Why does it fall at first even though Na⁺ ions are being added?

Select one answer

Hint 1Which ions are removed?

Hint 2H⁺ is exceptionally mobile.

Hint 3Na⁺ is much less conductive than H⁺.

Exam question

Hardest asked · about 5 min

3 marks

Describe and explain the shape of the conductivity graph when NaOH is added to ethanoic acid.

Hint 1Ethanoic acid is weak: few ions at the start.

Hint 2Neutralisation produces Na⁺ and CH₃COO⁻.

Hint 3After equivalence, excess OH⁻.

Where students lose marks on this one
  • Drawing a V shape like HCl.

    Why it happens: A weak acid starts with few ions.

    The first section rises, not falls.

Written for this site.

The graph below calculates conductivity from the ions present. Compare a strong acid (pKa below zero) with a weak one.

Conductivity during a titrationConductivity of 25.0 mL of 0.1 mol per litre strong acid (fully ionised) titrated with 0.1 mol per litre sodium hydroxide. It starts at 42.17 and reaches 6.32 millisiemens per centimetre at the equivalence point, 25.00 mL.equivalence05101520253035404550010203040volume of NaOH added (mL)conductivity (mS cm⁻¹)
  • conductivity
For a strong acid the graph is a V: very mobile H₃O⁺ ions are replaced by slower Na⁺ ions, then excess OH⁻ makes it rise steeply. A weak acid starts low because few ions are present, rises gently as salt forms, then steeply after equivalence. Either way the equivalence point is where the two straight sections meet.
-1.0
0.10 mol L⁻¹
0.10 mol L⁻¹
Acid
strong acid (fully ionised)
Starting conductivity
42.17 mS cm⁻¹
At equivalence
6.32 mS cm⁻¹ at 25.00 mL

Every slider is a normal range input, so the arrow keys move it one step and Home and End jump to the extremes.

Worked example4 marks

Reading an unknown acid from its titration curve

25.00 mL of a 0.100 mol L monoprotic acid is titrated with 0.100 mol L NaOH. The pH curve starts at 2.9, reads 4.8 at 12.50 mL, rises steeply from about 7 to 11 at 25.00 mL, and has pH 8.7 at equivalence. A conductivity probe in the same flask shows a gentle rise to 25.00 mL, then a steeper rise. Identify the type of acid, estimate its , and choose an indicator.

Strong or weak

Compare the starting pH and the equivalence pH with a strong acid.

A 0.100 mol L strong acid would start at pH 1.0 and reach equivalence at 7. This acid starts at 2.9 and reaches equivalence above 7, so it is a weak acid. Its conjugate base makes the solution basic at equivalence.

Ka from half-equivalence

At 12.50 mL, [HA] = [A⁻], so pH = pKa.

, so . Check: , giving pH 2.9, as observed.

Indicator

The colour change range must lie within the steep section and include the equivalence pH.

Phenolphthalein (8.3 to 10.0) fits. Methyl orange (3.1 to 4.4) would change colour in the buffer region, long before equivalence.

The conductivity graph

Link the gradient changes to the ions present.

Conductivity starts low because a weak acid has few ions. It rises gently as HA is converted into Na⁺ and A⁻, then more steeply after equivalence as fast-moving OH⁻ accumulates. The change in gradient at 25.00 mL confirms the equivalence point.

Answer

A weak acid with (consistent with ethanoic acid). Use phenolphthalein. Both graphs place equivalence at 25.00 mL.

Modelling neutralisation

Models help you see the particles, not just the pH. Useful media include:

  • online titration simulations that show the particles present at each stage;
  • physical models with counters for HA, A⁻, H₃O⁺ and OH⁻;
  • spreadsheets that compute the curve.

A good model of a weak acid shows most of it as intact HA molecules. OH⁻ reacts with HA directly, so HA and A⁻ coexist through the buffer region, and only A⁻ is left at equivalence.

Exam question

Harder · about 5 min

3 marks

Describe how neutralisation of a weak acid by a strong base could be modelled using a digital simulation or a physical model, and what the model should show that differs from a strong acid.

Hint 1What particles are present at the start?

Hint 2What happens as OH⁻ is added?

Hint 3What is left at equivalence?

Where students lose marks on this one
  • Showing all the acid ionised at the start.

    Why it happens: Weak acids are mostly un-ionised.

    Model the equilibrium.

Written for this site.

Worked example3 marks

A counter model of weak acid neutralisation

A class models 20 mL of ethanoic acid with counters: 10 HA counters in a tray, one of which is split into H₃O⁺ and A⁻. OH⁻ counters are added five at a time. Describe what the tray should contain at 0, 5, 10 and 15 OH⁻ counters, and relate each stage to the pH curve. Then say how the model would differ for HCl.

Start and half-way

OH⁻ reacts with HA directly: HA + OH⁻ → A⁻ + H₂O.

  • 0 OH⁻: nine HA, one H₃O⁺ and one A⁻. Mostly molecules, low but not very low pH.
  • 5 OH⁻: five HA and five A⁻. Equal amounts, so this is half-equivalence, where pH = pKa, in the middle of the buffer region.

Equivalence and beyond

Count what remains.

  • 10 OH⁻: ten A⁻ and no HA. Only the conjugate base is left, and it reacts slightly with water to make OH⁻, so the pH is above 7.
  • 15 OH⁻: ten A⁻ plus five unreacted OH⁻. The excess OH⁻ controls the pH, which is now high.

HCl compared

A strong acid is fully ionised from the start.

The HCl tray starts with ten H₃O⁺ and ten Cl⁻ and no molecules. Each OH⁻ removes an H₃O⁺. There is never a mixture of HA and A⁻, so there is no buffer region, and at equivalence only Na⁺ and Cl⁻ remain, giving pH 7.

Answer

The weak acid model shows HA and A⁻ side by side through the buffer region, equal amounts at half-equivalence, and only A⁻ (a weak base) at equivalence. The strong acid model shows only ions throughout and a neutral salt at equivalence. A simulation or spreadsheet can then check the pH predicted at each stage.

Back titrations

A back titration is used when the substance is insoluble, reacts slowly, or is volatile, so a direct titration has no sharp end point.

  1. Add a known excess of standard acid (or base).
  2. Titrate the leftover acid.
  3. Subtract: acid that reacted = total acid − leftover acid.

Worked example4 marks

Calcium carbonate in limestone

0.500 g of limestone is added to 50.00 mL of 0.200 mol L HCl. The excess HCl needs 20.00 mL of 0.100 mol L NaOH. Find the percentage by mass of CaCO₃ (100.09 g mol).

Total and excess acid

n = cV. The excess is found from the NaOH, 1 : 1.

Total HCl: mol. Excess HCl: mol.

Acid that reacted

Subtract.

mol.

Moles and mass of CaCO₃

CaCO₃ + 2HCl → CaCl₂ + H₂O + CO₂, so the ratio is 1 : 2.

mol, so g.

Answer

.

CheckpointAnswer before reading on.

Why is a back titration used to find the calcium carbonate content of a limestone sample?

Select one answer

Hint 1CaCO₃ is insoluble.

Hint 2Its reaction with acid is slow and gives off CO₂.

Hint 3A direct end point would be hard to see.

Exam question

Hardest asked · about 8 min

4 marks

A 0.500 g sample of impure limestone is added to 50.00 mL of 0.200 mol L HCl (excess). After the reaction, the remaining HCl requires 20.00 mL of 0.100 mol L NaOH. Calculate the percentage by mass of (100.09 g mol) in the sample.

Hint 1Total HCl = 0.0100 mol; excess HCl = n(NaOH) = 0.00200 mol.

Hint 2HCl reacted with CaCO₃ = 0.00800 mol.

Hint 3CaCO₃ : HCl = 1 : 2.

Where students lose marks on this one
  • Using the NaOH moles as the moles of CaCO₃.

    Why it happens: NaOH only measures the leftover acid.

    Subtract from the total.

Written for this site.

Analysis in industry and with digital instruments

  • Wine. Titratable acidity (mainly tartaric and malic acid) is measured by titration with NaOH to about pH 8.2. For red wine, a pH meter replaces the indicator because the colour hides it.
  • Pharmaceuticals. Titration checks the amount of active ingredient, for example aspirin or antacids, against the label.
  • Food and agriculture. Soil pH is tested before choosing crops or adding lime. Milk acidity shows freshness.
  • Mining and water treatment. Acid mine drainage and waste water are monitored, and neutralised with lime before release.

Digital probes and instruments.

  • pH probes with data loggers record the whole titration curve.
  • Conductivity probes allow conductometric titrations.
  • Autotitrators add titrant and find the end point automatically, which saves time and removes judgement of colour.

CheckpointAnswer before reading on.

A winery uses an automatic titrator with a pH probe to measure the total acid content of wine. Why is a pH probe used instead of an indicator?

Select one answer

Hint 1Red wine is strongly coloured.

Hint 2An indicator colour change would be hidden.

Hint 3The probe gives a titration curve.

CheckpointAnswer before reading on.

Which is an advantage of using a data logger with a pH probe during a titration?

Select one answer

Hint 1A logger records continuously.

Hint 2This gives the full curve.

Hint 3No colour judgement is needed.

Aboriginal and Torres Strait Islander Peoples' use of acid–base chemistry

Aboriginal and Torres Strait Islander Peoples have long used the chemical properties of natural materials.

  • Soap tree (Alphitonia excelsa). The Kuku Yalanji people rub its leaves with water to make a lather for washing. The leaves contain saponins, which act like soap.
  • Goat's foot (Ipomoea pes-caprae). Crushed leaves are applied to stings from stingrays and stonefish.
  • Ochre and white clay were eaten in small amounts to settle stomach upsets. Ochre contains basic iron oxides and hydroxides that neutralise excess stomach acid, and clays absorb irritants. This is the same chemistry as a modern antacid.

Exam question

Standard · about 5 min

3 marks

Describe one example of Aboriginal and Torres Strait Islander Peoples’ use of the acid–base properties of natural materials, and explain the chemistry involved.

Hint 1Consider ochre, clay, or plant preparations.

Hint 2What property does ochre have?

Hint 3Link to neutralisation or absorption.

Where students lose marks on this one
  • Describing the use without any chemistry.

    Why it happens: The question asks for the acid–base explanation.

    Name the reaction.

Written for this site.

Analysing household substances

SubstanceAcid analysedPoints to watch
Soft drinkphosphoric or citric acidDegas first: dissolved CO₂ forms carbonic acid, which would also react with NaOH.
Winetartaric acidUse a pH probe for red wine. Dilute the sample.
Juicecitric acid (triprotic)Use a 1 : 3 mole ratio. Filter pulp.
Antacid tabletCaCO₃ or Mg(OH)₂ (bases)Insoluble, so use a back titration with excess HCl.

CheckpointAnswer before reading on.

An antacid tablet containing insoluble CaCO₃ is analysed. Which method is most appropriate?

Select one answer

Hint 1CaCO₃ is insoluble in water.

Hint 2It reacts with excess acid.

Hint 3Then titrate what is left.

Exam question

Harder · about 6 min

3 marks

20.00 mL of orange juice is titrated with 0.0500 mol L NaOH, needing 18.60 mL. Assuming all the acid is citric acid, a triprotic acid (, 192.12 g mol), calculate its concentration in g L.

Hint 1n(NaOH) = 9.30 × 10⁻⁴ mol.

Hint 2Citric acid : NaOH = 1 : 3.

Hint 3Divide by 0.02000 L and multiply by M.

Where students lose marks on this one
  • Using a 1 : 1 ratio.

    Why it happens: Citric acid donates three protons.

    Divide n(NaOH) by 3.

Written for this site.

Exam question

Harder · about 5 min

3 marks

A student titrates a carbonated soft drink with NaOH to determine its acidity. Explain why the drink should first be degassed, and suggest how.

Hint 1Carbonated drinks contain dissolved CO₂.

Hint 2CO₂ forms carbonic acid.

Hint 3That would also react with NaOH.

Where students lose marks on this one
  • Saying CO₂ makes the drink basic.

    Why it happens: CO₂ is acidic in water.

    It forms carbonic acid.

Written for this site.

Buffers

A buffer contains a weak acid and its conjugate base in similar amounts, for example ethanoic acid and sodium ethanoate:

  • Added acid: extra H₃O⁺ reacts with CH₃COO⁻, shifting the equilibrium left (Le Chatelier's principle). Most of the added H₃O⁺ is removed.
  • Added base: OH⁻ reacts with CH₃COOH, forming CH₃COO⁻ and water. The equilibrium shifts right to replace H₃O⁺.

The pH changes only slightly. A buffer works best when (pH ≈ pKa), and its capacity is larger when both are more concentrated.

Worked example3 marks

Adding acid to a buffer

1.00 L of buffer contains 0.100 mol CH₃COOH and 0.100 mol CH₃COO⁻ (pKa 4.74). Find the pH after adding 0.010 mol HCl.

Reaction

The conjugate base consumes the added H₃O⁺ first.

CH₃COO⁻ + H₃O⁺ → CH₃COOH + H₂O, so HA becomes 0.110 mol and A⁻ becomes 0.090 mol.

New pH

Henderson–Hasselbalch with the new amounts.

.

Answer

pH 4.66, a fall of only 0.09. The same acid in 1.00 L of pure water would take the pH from 7 to 2.

Exam question

Harder · about 4 min

2 marks

A buffer contains 0.20 mol L and 0.10 mol L (p = 4.74). Calculate its pH.

Hint 1.

Hint 2Ratio = 2.

Hint 3log 2 = 0.30.

Where students lose marks on this one
  • Inverting the ratio.

    Why it happens: [A⁻] (the base) goes on top.

    Base over acid.

Written for this site.

Exam question

Hardest asked · about 6 min

3 marks

1.00 L of buffer contains 0.100 mol and 0.100 mol (p = 4.74). 0.010 mol HCl is added. Calculate the new pH.

Hint 1H⁺ reacts with A⁻: A⁻ + H⁺ → HA.

Hint 2HA becomes 0.110, A⁻ becomes 0.090.

Hint 3Use the ratio.

Where students lose marks on this one
  • Adding the H⁺ to the buffer pH directly.

    Why it happens: The added acid is consumed by the conjugate base.

    Update the moles first.

Written for this site.

Exam question

Harder · about 7 min

4 marks

Describe an investigation to prepare an ethanoic acid/ethanoate buffer and demonstrate its properties.

Hint 1Mix equal moles of CH₃COOH and CH₃COONa.

Hint 2Compare with water as a control.

Hint 3Add small equal amounts of acid and base.

Where students lose marks on this one
  • Using HCl and NaCl to make the buffer.

    Why it happens: A buffer needs a weak acid and its conjugate base.

    Strong acids cannot buffer.

Written for this site.

Buffers in natural systems

Blood is held at pH 7.35 to 7.45, mainly by the carbonic acid/hydrogen carbonate buffer:

  • Acid from metabolism (such as lactic acid in exercise) shifts the equilibrium left. The extra CO₂ is breathed out, so breathing rate helps control pH.
  • The kidneys excrete H⁺ and adjust HCO₃⁻ over longer times.
  • Proteins and phosphate ions also buffer.

This matters because enzymes and haemoglobin only work over a narrow pH range. A small shift causes acidosis or alkalosis, which can be fatal.

Oceans are buffered by the same carbonate system. HCO₃⁻ is the main species at pH about 8.1, because that is well below pKa₂ (10.3). As the oceans absorb more CO₂, the equilibria shift to produce H⁺, which reacts with CO₃²⁻. Less carbonate makes it harder for corals and shellfish to build CaCO₃ shells.

CheckpointAnswer before reading on.

Sea water has a pH of about 8.1. For , p ≈ 10.3. Which species is present in greater concentration in sea water?

Select one answer

Hint 1.

Hint 2pH is 2.2 units below pKa.

Hint 3So the ratio is about 10⁻²·².

Exam question

Harder · about 7 min

4 marks

Explain how the carbonic acid/hydrogen carbonate buffer, , keeps blood pH within its narrow range when acid enters the blood, and why this matters.

Hint 1Extra H₃O⁺: which way does it shift?

Hint 2What removes the extra H₂CO₃?

Hint 3Why is a narrow pH range important?

Where students lose marks on this one
  • Saying the buffer removes all the acid.

    Why it happens: Buffers minimise, not eliminate, pH changes.

    Say the change is small.

Written for this site.

Common mistake

A buffer keeps the pH perfectly constant.

Why it happens: Buffers are described as resisting pH change.

A buffer reduces a change in pH; it does not prevent it. The pH still moves a little, and if you add more acid than there is conjugate base, the buffer is used up and the pH falls sharply.

What lifts this to a Band 6

In any titration answer, show every line: moles of the known, mole ratio, moles of the unknown, concentration, and the dilution factor. In curve questions, always give three things for each curve: the starting pH, the pH at equivalence (with the reason, which is salt hydrolysis), and a suitable indicator.

Compare the buffer with pure water below. Then change the ratio of to to move the starting pH, and increase both to widen the flat region.

How a buffer resists pH changeA buffer of 0.1 mol per litre HA and 0.1 mol per litre A⁻ with pKa 4.8 has pH 4.80. It takes 8.20 millimoles of strong acid to lower it by one unit.pKa-20-15-10-50510152002468101214strong acid (−) or strong base (+) added (mmol)pH
  • pure water
  • buffer
The buffer’s pH starts at pKa + log([A⁻]/[HA]). Adding H₃O⁺ converts A⁻ to HA, and adding OH⁻ converts HA to A⁻, so the ratio changes only slowly. Make the buffer more concentrated and the flat region widens: that is buffer capacity.
4.8
0.10 mol L⁻¹
0.10 mol L⁻¹
Buffer pH, pKa + log([A⁻]/[HA])
4.80
Strong acid to lower the pH by 1
8.20 mmol
Same acid added to 100 mL of water
pH 1.09

Every slider is a normal range input, so the arrow keys move it one step and Home and End jump to the extremes.

Why indicators change colour

An indicator is itself a weak acid, HIn, whose two forms have different colours:

By the Henderson–Hasselbalch relation, the eye sees the colour change when the ratio moves from about 1 : 10 to 10 : 1. So the change happens over roughly . You use only a few drops, so the indicator does not affect the titre noticeably.

Polyprotic acids

A curve for a diprotic acid such as H₂CO₃, or for Na₂CO₃ titrated with HCl, has two steep sections, one for each proton. For Na₂CO₃ with HCl:

  • phenolphthalein detects the first equivalence (CO₃²⁻ → HCO₃⁻);
  • methyl orange detects the second (HCO₃⁻ → H₂CO₃).

This is why the full 1 : 2 ratio needs methyl orange when you standardise HCl against sodium carbonate.